|
High-Speed Emulation for Texas Instruments DSP |
 |
 |
 |
Blackhawk offers a wide range of JTAG Emulators for exas Instruments Digital Signal Prozessors (DSP). At the "low end", tiny, extremely portable USB powered emulators supportting a variety of DSP families are available at affordable prices ( USB510, USB510L, USB2000) .
Furthermore, Blackhawk offers several XDS560-compatible emulators for PCI, USB and LAN and the high-performance XDS560Trace system which allows for deep insight to complex internal processes such as the detection of spurious problems which are hard to track down with standard emulation methods. A comparative table describing the most important features of all Blackhawk emulation products in detail is now online at their website.
Important Note: Customers who have recently purchased Code Composer Studio 3.3 are eligible to free upgrades to Code Composer Studio 4.x under provisions described here. |
|
|
USB560BP bus-powered USB2.0 Emulator |
|
|
|
|
The Blackhawk USB560BP is the only bus-powered USB JTAG Emulator that supports all of the advanced capabilities of Texas Instruments latest DSPs. These capabilities include high-speed Real-Time Data Exchange (RTDX)™, lightning speed downloads and Advanced Event Triggering to quickly find and fix real-time software problems.
The emulator pod, which is under 5 ounces in weight, does not require an external power supply! Features include a variable TCK (timing clock) up to 50 MHz and highly flexible 6 inch cable assembly suitable for use from 5.0 volts down to 0.5 volts to support TI low-voltage device roadmap.
The Blackhawk USB560BP-JTAG-Emulator supports all TMS320-, TMS470- (ARM®) and OMAP™ families.
Read more ... |
|
Last Updated on Tuesday, 25 May 2010 21:54 |
|
USB-JTAG Emulator for Beginners: BH-USB100 |
|
|
|
|
 The Blackhawk™ USB100 (v1.0) is a very low-cost controller for basic debugging of Texas Instruments DSPs. Requiring no external power source, the USB100 can support most of the basic features of higher priced emulators and requires no additional drivers when installed using CCS V3.3 SR12 and CCS v3.3 for C2000 DSK Version (version 3.3.81.28 or newer). The USB100 is also fully supported under CCstudio V4.0 and future Texas Instruments roadmap software development environments. Blackhawk’s USB100 provides additional features and performance not found in other XDS100 emulators. The USB100 provides for faster code downloads and assembly code stepping in that the USB100 uses a high-speed USB2.0 (480 Mb/s) port instead of slower USB1.x (12 Mb/s) implementations - at only 99 EUR each plus shipping and VAT.
The USB100 will support 1.8-3.3V targets with standard TI 14-pin connections and also supports the Texas Instruments compact 20-pin emulation header (cTI). Additionally, with an optional 20cTI to 20ARM connector (available from Blackhawk), the USB100 can connect to ARM Multi-Ice platforms. The USB100 Controller is also compatible with Code Composer Studio™ Flash-burner utility.
For inquiries about the USB100 JTAG Emulator please use our Contact Form.
|
|
Last Updated on Tuesday, 25 May 2010 11:05 |
|
BH-XDS-560T Trace Emulator |
|
|
|
|
Please be informed that the XDS560 Trace system will be discontinued. Once supplies are gone, we will be not accept orders for the Trace system any more.
The Blackhawk™ XDS560 Trace System (XDS560 Trace) is non-intrusive, hardware-based trace tool for debugging and profiling high-performance, DSP-based applications providing developers with advanced visibility to debug specialized problems that occur in high-performance, real-time embedded applications. This real-time visibility produces the detailed information needed to determine where complex and intermittent problems occur as well as the ability to analyze, profile, and tune applications for optimal performance.
The XDS560 Trace System is available in several configurations or as add-on to your existing Blackhawk XDS560-class emulator.
Read more...
For more information, please contact us. |
|
Last Updated on Tuesday, 25 May 2010 11:12 |
|
BH-USB2000 Emulator for C2000 DSP Controllers |
|
|
|
|
 The Blackhawk USB2000 JTAG-Controller is a small and lightweight controller designed for the unique requirements of the Texas Instruments TMS320C2000 developers. Bundles with Texas Instruments' Code Composer Studio for C2000 (TMDSCCS2000-1, TMDSCCS-MCUxxx), this tool delivers the best price performance.
Built upon the advanced technology of the highly-popular USB510, this 3rd generation controller achieves the cost/performance balance required by the C2000 development community. The compact controller pod requires no external power source. Power is derived directly from the PC’s USB port.
An optional isolation adapter is available to protect this tool and the attached PC from ESD and ground loops in harsh environments.
Read more or contact us for for information. |
|
Last Updated on Wednesday, 02 June 2010 09:02 |
|
BH-USB510L USB-JTAG-Emulator |
|
|
|
|
The Blackhawk™ USB510L JTAG Emulator is a very affordable and full-featured addition to our product lineup for Texas Instruments TMS320, TMS470 (ARM), DaVinci and OMAP families.Two optional add-ons to the USB510L are the Blackhawk FlashBurn utility and Blackhawk Isolation Adapter.
BHFlashBurn is a scriptable utility that follows the freely available Texas Instruments API and algorithms for programming DSPs with on-chip flash. The Blackhawk Isolation Adapter which protects from ground loop voltage, harsh environments and new, untested designs. Supports 3.3-5.0v targets with TI 14-pin connections.
Unlike the BH-USB510, this emulator does NOT support legacy DSP devices such as the TMS320VC33 or TMS320C20x.
Read more ...
For more information, please contact us.
|
|
Last Updated on Tuesday, 25 May 2010 11:13 |
|
BH-USB560m USB2.0 JTAG-Emulator |
|
|
|
 The Blackhawk USB560 JTAG emulator is the third generation of the most widely used USB XDS560-class emulator, first introduced by Blackhawk in 2002. The USB560 supports all of the advanced capabilities of Texas Instruments latest DSPs. These capabilities include high-speed Real-Time Data Exchange HS-RTDX™, lightning speed downloads and Advanced Event Triggering to quickly find and fix real-time software problems.
The compact JTAG emulator pod features a variable TCK (timing clock) up to 50 MHz and supports voltages from 5v down to 0.5v to support TI low-voltage device roadmap. The USB560 JTAG Emulator is also compatible with the Code Composer Studio Flash-burner utility.
Read more ...
For more information, please contact us. |
|
Last Updated on Tuesday, 25 May 2010 11:13 |
|
BH-LAN560 USB2.0/LAN-JTAG-Emulator |
|
|
|
|
 The LAN560 JTAG Emulator (LAN560) is the most advanced XDS560-class product by Blackhawk, the first of its class for debugging TI DSPs across Ethernet. The LAN560 JTAG emulator supports all of the advanced capabilities of Texas Instruments latest DSPs. These capabilities include high-speed Real-Time Data Exchange (RTDX)™, for lightning speed downloads and Advanced Event Triggering to quickly find and fix real-time software problems. Connections are made through its auto-sensing 10/100 Mbps RJ45 connector that attaches directly to any hub, switch, or wireless access point on the network. Alternatively, the BH-LAN560 kann be used on a local computer through its built-in USB2.0 high-speed port.
Read more or contact us for more information. |
|
Last Updated on Tuesday, 25 May 2010 11:13 |
|
BH-USB510 Bus-Powered JTAG-Emulator |
|
|
|
 The Blackhawk™ USB510 JTAG Emulator is the ultra-compact XDS510™-class offering in our high-performance JTAG Emulator lineup for Texas Instruments TMS320, TMS470 (ARM) and OMAP families. The credit card sized USB510 JTAG Emulator is the most compact and lightweight JTAG emulator available. The high-speed USB 2.0 port operates at 480 Mbits/second and is Plug n’ Play compatible with Windows®. Software compatibility with all versions of Code Composer and Code Composer Studio including v2.2 and above, and a driver independent DLL developed by Blackhawk, assures existing and future device compatibility for legacy or new DSPs right out of the box with no upgrades required. The Blackhawk USB510 includes legacy support for Code Composer v4.1x and CCStudio v1.2 which gives users access and compatibility to VC33, C20x and C24x. The USB510 JTAG Emulator is also compatible with Code Composer Studio™ Flash-burner utility. |
|
Last Updated on Tuesday, 25 May 2010 11:13 |
|
BH-PCI560 High-Speed JTAG-Emulator |
|
|
|
 The Blackhawk PCI560 is the third generation of the widely used XDS560-class emulator first introduced by Blackhawk and the only half-height and half-length XDS560 JTAG Emulator that supports all of the advanced capabilities of Texas Instruments latest DSPs. Features include a variable TCK (timing clock) up to 50 MHz and includes a detachable, 5 1/2 foot multi-voltage cable/pod assembly suitable for use from 5.0 volts down to 0.5 volts to support TI low-voltage device roadmap.
|
|
Last Updated on Tuesday, 25 May 2010 11:14 |
|
|
|
|
|
JTAG-Emulators
